View and Download Samsung GALAXY J7 V user manual online. GALAXY J7 V Cell Phone pdf manual download. Galaxy j7 v user manual. Check out our support resources for your Galaxy J7 V (2018) SM-J737V to find manuals, specs, features, and FAQs. You can also register your product to gain access to Samsung's world-class customer support.
Notice: These directions are for a Model 18 sharpener. Models 19 and 17 are generally replaced the same way - directions for those models will be added too so that the specifics and photos match and cover anything that is different on those types of sharpeners. You can click on any of these photos for a close-up. At any time when you are handling the blade assembly, take measures to protect your hands! (guideline suggestions for this are in step 5)Step 1 - Set up the sharpener as you would when it is ready to use. Tip it slightly forward and tap on the top of the sharpener a few times. This is to shake pencil shaving into the bin. Remove and dump the bin. Unplug the sharpener (safety first!) and turn it over as shown in the picture. Remove the 3 screws from bottom of the case. Yay! somebody already did this one for me! (heh.ok.that was lame)
Step 2- Remove the bottom cover from the case and put it somewhere safely out of the way. Put the mounting screws in this cover (turn it up with the feet down and use it like a holding tray). If you replaced the shavings bin (as shown in the picture), remove it and set it aside until after the repair is complete. Make sure you keep the screws separate from the housing cover screws (will be removed later). Putting the wrong screws in the wrong place can lead to a loose fit and your sharpner may buck and kick instead of running smoothly.
Hunt Boston Model 18 or 19 Pencil Electric Sharpener Replacement Gear: $12. Replacement part for the Boston Model 18 or Model 19 electric pencil sharpener. This will NOT work on a Model 17 sharpener. THESE HAVE BEEN FIT-TESTED SO THERE SHOULD BE NO. The caliber, serial number and model name on each barrel or frame. Take note of this information, record it on the warranty page in this manual and be prepared to state it when contacting the Traditions Customer Service Department with your questions. Contact Traditions at. Apr 13, 2015 Boston Model 18/19 Pencil Sharpener Gear. By brianwsimms. Drive Gear for Model 17 Pencil Sharpener by mklange is licensed under the Creative Commons - Attribution - Non-Commercial license. Liked By View All Give a Shout Out If you print this Thing and display it in public proudly give attribution by printing and displaying this tag.
BOSTON DESKTOP ELECTRIC Pencil Sharpener Model 19 Vintage Hunt USA Made TESTED - $16.99. Classic Boston electric desktop pencil sharpener in white/gray. Model #19, made in the United States by Hunt Manufacturing of Statesville, North Carolina. Model 41 – replace with Elmer’s item R1827 Dull point after sharpening (sharpeners with helical cutters) Usually caused by cutter wear – see “Rough Sharpening” above. Pencils tips are normally sharpened to a usable (but not excessively sharp) point. As the cutters wear, the size.
Boston Hunt Model 18 User's Manual Download
Step 3 - Lift the sharpener assembly out of the case. The center plate holds the motor on one side (right in figure shown) and the sharpening blade and housing on the other side (shown at left). For this repair, you will NOT be removing or loosening anything from motor assembly.
Step 4 - Remove the screws shown and set them aside so they will not be exchanged with the screws that hold the case cover. Pull the blade housing gently back and let it lay to the side while you swap (or install) the replacement gear.
Step 5 - Here is a front view of the blade housing removed and set t0 the side, wires still connected. In view are the blade assembly and a blade assembly guide. This guide has gear teeth that match the a gear that is part of the sharpening blade assembly.
In this side view, you see the blade gear, the blade assembly guide, and the blade assembly. Again, if you are replacing a gear that has completely broken, you may be removing pieces from inside the case rather than just swapping the gear.
Using a cloth or thick wrapping of paper towel or a work glove (make sure you do something to protect your hand from getting cut by the blade), get a grip on the blade assembly and pull it back to remove it from the sharpener. It may take some force to do this if there is still a gear or portion of the gear intact.
Notice that the shaft on the blade assembly has some flat side sections on it near the end. If you examine the shaft-mount on the gear, you will see that it also has flat portions in the end face that match up with the shaft . This locks the shaft in and keeps it from free-spinning so the gear will drive the blade assembly when it is turned by the motors main drive that engages to this gear.
Step 6 - Do a test fit of the blade assembly to the gear. This step does not take long and will familiarize you with what it takes to get a proper fit and aligment of the parts when they are replaced into the sharpener.
Step 7 - if the blade assembly guide came out when you removed the blade assembly, mount it back to the plate. Notice the proper direction and flush fit to the center plate as shown in the figure.
Step 8 - work the blade assembly shaft partially back into the guide and through the hole in the center plate. Place the replacement gear with it's collar section and shaft mount facing the center plate. Turn the blade assembly and match it up to the shaft mount in the gear's collar, then snap it fully into place. This should align the gear so it meshes with the small drive gear on the motor.
Step 9 - Replace the blade assembly cover back over the blade assembly. Fasten it back to the center plate with the mounting screws. Re-assemble the sharpener by working your way backwards through steps 3, 2, 1 and you should have lift-off!